Check HP Laptop Battery Health Status Complete Detailed information

All Nokia Codes

*** WARNING: Using secret codes may be harmful to your phone and result in disabling or worse. Use these Nokia codes at your own discretion, we accept no responsiblility for blocked phones while using these codes!!!

IMEI Number *#06#

Cells Identity Code (IMEI = International Mobile Equipment Identity) XXXXXX XX XXXXXX X TAC FAC SNR SP TAC=Type Approval Code (first 2 digits = country code of the approval-country)
FAC = Final Assembly Code: (01,02 = AEG) (10,20 Nokia) (40,41,44 Siemens) (30 Ericsson) (50 Bosch) (51 Sony, Siemens ,Ericsson) (60 Alcatel) (65 AEG)
(70 Sagem) (75 Dancall) (80 Philips) (85 Panasonic) SNR = Serial Nr. SP = Spare (always "0") Software Version

1. *#0000# shows the software version Signal Processing
2. *3370# - Enchanced full Rate Codec (EFR) activation. It will automatically restart.
3. #3370# - Enchanced full Rate Codec (EFR) deactivation.
4. *4720# - Half Rate Codec activation. It will automatically restart.
5. #4720# - Half Rate Codec deactivation

Enchanced Full Rate will give you much better sound quality when you enable it. The new Enhanced Full Rate CODEC adopted by GSM uses the ASELP (Algebraic Code Excitation Linear Prediction) compression technology. This technology allows for much great voice quality in the same number of bits as the older Full Rate CODEC. The older technology was called LPC-RPE (Linear Prediction Coding with Regular Pulse Excitation). Both operate at 13 kilobits (but you take up more space on the network, so they can charge you more) - Talk-time is reduced with about 5%

Nokia E-Series Secret Codes

1. Check software version and the release number of your device: *#0000#
2. See WLAN MAC address: *#62209526#
3. See Bluetooth MAC address: *#2820#
4. To hard reset and restore to factory settings: *#7370# (default lock code is
5. See IMEI (International Mobile Equipment Identity) number: *#06#
6. Check number where calls are diverted: *#61#
7. To display your phone's life timer, type: #92702689#

Please use the following two codes with extreme care

1. To soft reset the phone and reset phone settings type: *# 7780#
2. To hard reset and completely erase all data on the phone and restore it to factory settings, type *#7370#. You'll be asked for a lock code. The default Nokia lock code is 12345.
3. Sim Clock Stopping *#746025625# [*#sim0clock#]
4. Checks if the sim clock can be stopped. Sim clock stop is a kind of stand-by mode which will save battery time. This code doesn't work with software version 4.59. It will tell you if it can be stopped or not.

Warranty Menu *#92702689# takes you to a secret menu with 6 choices: [*#warranty#]

i. Displays Serial Number.
ii. Displays the Month and Year of Manufacture (0997).
iii. Displays (if there) the date where the phone was purchased (MMYY).
iv. Displays the date of the last repairment - if found (0000).
v. Makes you capable of transferring user data if you have the gear for it.
vi. Shows how long the phone has been used to talk. This counter is not reset by you when "clear timers" like the counters in the call register.

Bypass the SP lock With a Nokia 16xx/21xx/31xx/51xx/81xx:

1. Insert SIM card of different provider.
2. Turn on the phone and press the UP VOLUME key for 3 sec. Then release it and the phone says PIN CODE?
3. Press the "C" key.
4. Then Press * and wait until it disappears and appears again, then press * one more time and 04*PIN*PIN*PIN#

Nokia Speed Trap Detector Urban Legend spread by Nokia Engineers:

The settings for radar speed traps detector. Your Nokia cell phone can be programmed to pick up radar speed traps, when programmed your cell phone picks up the radar and alerts you on the message alert tone. (Doesn't work with Nokia 7110!)

1. Enter your menu
2. Select settings
3. Select security settings
4. Select closed user group
5. Select on
6. Enter 00000
7. Press OK
8. Clear back to normal, within a few seconds your phone will display a radar sign with five zero's next to it. It is now activated.

Unfortunately only Nokia phones have this function. The Cell Phone info display needs to be deactivated. Settings ->Phone Settings ->Cell Info display. Each time you turn off your phone, or even each time you loose contact with your carrier, you'll have to activate it again... It is done using steps 1 through 5 above, but the number (00000) will be already on the field as a default.

About CCN World Tech

CCN World Tech is a platform specifically dedicated in providing latest tech related news and articles around the world. We also tutor people on how to get the best out of their handheld and tech pertaining devices. You can follow us on Facebook, Twitter, and Pinterest.
    Post Comment

Disclaimer: Information provided on CCN World Tech were verified and were deemed to be accurate, but notwithstanding, they are subjected to be edited, rewritten, or modified at anytime.